How to set up Scisky FC step by step


#81

Got it all sorted out and flying finally… pwm 32000, all channels scaled 125% on the tx and fiddled with the throttle trim. Thanks for all the suggestions guys! The yaw is really slow almost nonexistent, but I will figure it out. I also need to set up modes switch.


#82

:+1:
If you want faster yaw, increase your yaw rate in the PID tuning tab.

I also recommend to set your RC Rate (receiver tab) to 1.0.


#83

:clap::+1::clap::+1: perfekt


#84

Hi everyone. despite all the good info here, YT and rcforums on how to get this lil board up and running, after 2 days of trying I still cant get it to bind to my devo 7e with deviation v5. ive used the radio and model configs, and followed the online guides, from here (and elsewhere) to no avail.
even tried betaflight… all I ever get is fast blinking red led.
can see FC in cleanflight just fine, just cant get the bugger to bind.

could it be a bad devo? ( it works fine with my syma’s…but also wont bind to cx-10 or hubsan x4)

thanks!


#85

I’m not a devo guy, but did you choose dsm2 protocol on your tx?
I’m sure other devo users here know exactly what to do and will chime in to help.

Maybe this vid helps. It’s about binding a orange dsm2 rx, but I think binding a scisky rx should be the same.


#86

Syma? So you have nrf24L01 module in your devo? Which should work with CX-10 too. Are you sure you have correct configurations? Of course CYRF-module could be broken, especially if you have now soldered new connections to it.

But assuming your CYRF-module works, you could paste your CLI-dump here so your configuration could be checked?


#87

And hubsan requires A7105 module.


#88

Is there anyway to tune out the bouncing / jumpy flight characteristics when flying a lil 50g auw 8.5mm quad in light wind? I thought I got it tuned perfectly until it started getting a lil windy (5-12mph) and it wants to bounce around. Maybe its just too light and it being 120mm makes it impossible to fly smooth with lil wind gusts. I swear I’ve seen others fly smooth though in the conditions that are here…


#89

With brushed micro quads? I somewhat doubt that - it’s maybe possible but with those conditions something with a little more power might be the more reliable approach.


#90

thanks. yep DSM2. watched that video yesterday. :slight_smile:
@nuffe yep. got the cx-10 working (blue board)
I have no other FC to check the CYRF module with. I looked at the joints with magnifying glass, but since my nrf is working… ?
`# dump

version

BetaFlight/NAZE 2.7.1 May 16 2016 / 20:45:45 (74cd38a)

dump master

mixer

mixer QUADX
mmix reset
smix reset

feature

feature -RX_PPM
feature -VBAT
feature -INFLIGHT_ACC_CAL
feature -RX_SERIAL
feature -MOTOR_STOP
feature -SERVO_TILT
feature -SOFTSERIAL
feature -GPS
feature -FAILSAFE
feature -SONAR
feature -TELEMETRY
feature -CURRENT_METER
feature -3D
feature -RX_PARALLEL_PWM
feature -RX_MSP
feature -RSSI_ADC
feature -LED_STRIP
feature -DISPLAY
feature -ONESHOT125
feature -BLACKBOX
feature -CHANNEL_FORWARDING
feature -TRANSPONDER
feature VBAT
feature RX_SERIAL
feature MOTOR_STOP

beeper

beeper GYRO_CALIBRATED
beeper RX_LOST
beeper RX_LOST_LANDING
beeper DISARMING
beeper ARMING
beeper ARMING_GPS_FIX
beeper BAT_CRIT_LOW
beeper BAT_LOW
beeper GPS_STATUS
beeper RX_SET
beeper ACC_CALIBRATION
beeper ACC_CALIBRATION_FAIL
beeper READY_BEEP
beeper MULTI_BEEPS
beeper DISARM_REPEAT
beeper ARMED
beeper SYSTEM_INIT
beeper ON_USB

map

map TAER1234

serial

serial 0 1 115200 57600 0 115200
serial 1 64 115200 57600 0 115200

led

led 0 15,15:ES:IA:0
led 1 15,8:E:WF:0
led 2 15,7:E:WF:0
led 3 15,0:NE:IA:0
led 4 8,0:N:F:0
led 5 7,0:N:F:0
led 6 0,0:NW:IA:0
led 7 0,7:W:WF:0
led 8 0,8:W:WF:0
led 9 0,15:SW:IA:0
led 10 7,15:S:WF:0
led 11 8,15:S:WF:0
led 12 7,7:U:WF:0
led 13 8,7:U:WF:0
led 14 7,8:D:WF:0
led 15 8,8:D:WF:0
led 16 8,9::R:3
led 17 9,10::R:3
led 18 10,11::R:3
led 19 10,12::R:3
led 20 9,13::R:3
led 21 8,14::R:3
led 22 7,14::R:3
led 23 6,13::R:3
led 24 5,12::R:3
led 25 5,11::R:3
led 26 6,10::R:3
led 27 7,9::R:3
led 28 0,0:::0
led 29 0,0:::0
led 30 0,0:::0
led 31 0,0:::0

color

color 0 0,0,0
color 1 0,255,255
color 2 0,0,255
color 3 30,0,255
color 4 60,0,255
color 5 90,0,255
color 6 120,0,255
color 7 150,0,255
color 8 180,0,255
color 9 210,0,255
color 10 240,0,255
color 11 270,0,255
color 12 300,0,255
color 13 330,0,255
color 14 0,0,0
color 15 0,0,0

aux

aux 0 2 0 950 1450
aux 1 0 0 900 900
aux 2 0 0 900 900
aux 3 0 0 900 900
aux 4 0 0 900 900
aux 5 0 0 900 900
aux 6 0 0 900 900
aux 7 0 0 900 900
aux 8 0 0 900 900
aux 9 0 0 900 900
aux 10 0 0 900 900
aux 11 0 0 900 900
aux 12 0 0 900 900
aux 13 0 0 900 900
aux 14 0 0 900 900
aux 15 0 0 900 900
aux 16 0 0 900 900
aux 17 0 0 900 900
aux 18 0 0 900 900
aux 19 0 0 900 900

adjrange

adjrange 0 0 0 900 900 0 0
adjrange 1 0 0 900 900 0 0
adjrange 2 0 0 900 900 0 0
adjrange 3 0 0 900 900 0 0
adjrange 4 0 0 900 900 0 0
adjrange 5 0 0 900 900 0 0
adjrange 6 0 0 900 900 0 0
adjrange 7 0 0 900 900 0 0
adjrange 8 0 0 900 900 0 0
adjrange 9 0 0 900 900 0 0
adjrange 10 0 0 900 900 0 0
adjrange 11 0 0 900 900 0 0
adjrange 12 0 0 900 900 0 0
adjrange 13 0 0 900 900 0 0
adjrange 14 0 0 900 900 0 0

rxrange

rxrange 0 1000 2000
rxrange 1 1000 2000
rxrange 2 1000 2000
rxrange 3 1000 2000

servo

servo 0 1000 2000 1500 90 90 100 -1
servo 1 1000 2000 1500 90 90 100 -1
servo 2 1000 2000 1500 90 90 100 -1
servo 3 1000 2000 1500 90 90 100 -1
servo 4 1000 2000 1500 90 90 100 -1
servo 5 1000 2000 1500 90 90 100 -1
servo 6 1000 2000 1500 90 90 100 -1
servo 7 1000 2000 1500 90 90 100 -1

set mid_rc = 1500
set min_check = 1100
set max_check = 1900
set rssi_channel = 0
set rssi_scale = 30
set rssi_ppm_invert = OFF
set input_filtering_mode = OFF
set rc_smoothing = ON
set roll_yaw_cam_mix_degrees = 0
set max_aux_channels = 6
set debug_mode = NONE
set min_throttle = 1000
set max_throttle = 2000
set min_command = 1000
set servo_center_pulse = 1500
set 3d_deadband_low = 1406
set 3d_deadband_high = 1514
set 3d_neutral = 1460
set 3d_deadband_throttle = 50
set unsynced_fast_pwm = OFF
set fast_pwm_protocol = ONESHOT125
set motor_pwm_rate = 32000
set servo_pwm_rate = 50
set disarm_kill_switch = ON
set gyro_cal_on_first_arm = OFF
set auto_disarm_delay = 5
set small_angle = 25
set fixedwing_althold_dir = 1
set reboot_character = 82
set serialrx_provider = SPEK1024
set sbus_inversion = ON
set spektrum_sat_bind = 0
set spektrum_sat_bind_autoreset = 1
set telemetry_switch = OFF
set telemetry_inversion = OFF
set frsky_default_lattitude = 0.000
set frsky_default_longitude = 0.000
set frsky_coordinates_format = 0
set frsky_unit = IMPERIAL
set frsky_vfas_precision = 0
set frsky_vfas_cell_voltage = OFF
set hott_alarm_sound_interval = 5
set battery_capacity = 0
set vbat_scale = 110
set vbat_max_cell_voltage = 43
set vbat_min_cell_voltage = 33
set vbat_warning_cell_voltage = 35
set vbat_hysteresis = 1
set vbat_pid_compensation = OFF
set current_meter_scale = 400
set current_meter_offset = 0
set multiwii_current_meter_output = OFF
set current_meter_type = ADC
set align_gyro = DEFAULT
set align_acc = DEFAULT
set align_mag = DEFAULT
set align_board_roll = 0
set align_board_pitch = 0
set align_board_yaw = 0
set max_angle_inclination = 700
set gyro_lpf = OFF
set gyro_sync_denom = 8
set gyro_lowpass = 100
set moron_threshold = 32
set imu_dcm_kp = 2500
set imu_dcm_ki = 0
set alt_hold_deadband = 40
set alt_hold_fast_change = ON
set deadband = 0
set yaw_deadband = 0
set throttle_correction_value = 0
set throttle_correction_angle = 800
set yaw_control_direction = 1
set yaw_motor_direction = 1
set yaw_jump_prevention_limit = 200
set tri_unarmed_servo = ON
set servo_lowpass_freq = 400
set servo_lowpass_enable = OFF
set super_expo_factor = 30
set super_expo_factor_yaw = 30
set super_expo_yaw = OFF
set failsafe_delay = 10
set failsafe_off_delay = 10
set failsafe_throttle = 1000
set failsafe_kill_switch = OFF
set failsafe_throttle_low_delay = 100
set failsafe_procedure = OFF
set rx_min_usec = 985
set rx_max_usec = 2115
set gimbal_mode = NORMAL
set acc_hardware = AUTO
set acc_lpf_hz = 10.000
set accxy_deadband = 40
set accz_deadband = 40
set acc_unarmedcal = ON
set acc_trim_pitch = 0
set acc_trim_roll = 0
set baro_tab_size = 21
set baro_noise_lpf = 0.600
set baro_cf_vel = 0.985
set baro_cf_alt = 0.965
set baro_hardware = AUTO
set mag_hardware = AUTO
set mag_declination = 0
set pid_process_denom = 2
set blackbox_rate_num = 0
set blackbox_rate_denom = 0
set blackbox_device = SERIAL
set magzero_x = 0
set magzero_y = 0
set magzero_z = 0

rxfail

rxfail 0 a
rxfail 1 a
rxfail 2 a
rxfail 3 a
rxfail 4 h
rxfail 5 h
rxfail 6 h
rxfail 7 h
rxfail 8 h
rxfail 9 h
rxfail 10 h
rxfail 11 h
rxfail 12 h
rxfail 13 h
rxfail 14 h
rxfail 15 h
rxfail 16 h
rxfail 17 h

profile

profile 0
############################# PROFILE VALUES ####################################

set yaw_p_limit = 500
set dterm_lowpass = 110
set dynamic_pterm = ON
set iterm_always_reset = OFF
set iterm_reset_degrees = 200
set yaw_iterm_reset_degrees = 50
set iterm_reset_offset = 15
set yaw_lowpass = 80
set pid_controller = MWREWRITE
set p_pitch = 45
set i_pitch = 35
set d_pitch = 18
set p_roll = 45
set i_roll = 35
set d_roll = 18
set p_yaw = 90
set i_yaw = 40
set d_yaw = 0
set p_alt = 50
set i_alt = 0
set d_alt = 0
set p_level = 50
set i_level = 50
set d_level = 100
set p_vel = 55
set i_vel = 55
set d_vel = 75
rateprofile 0

rateprofile

rateprofile 0

set rc_rate = 100
set rc_expo = 60
set rc_yaw_expo = 20
set thr_mid = 50
set thr_expo = 0
set roll_rate = 50
set pitch_rate = 50
set yaw_rate = 50
set tpa_rate = 20
set tpa_breakpoint = 1650

`


#91

Hi @chrisdo, very good guide! Just would like to suggest something that I found out by accident.
At a certain point, I could not get my dx6i to bind to my second scisky. I tried all the tricks, but eventually got it to bind my putting all sticks in the center position, so also the throttle at midstick… Haven’t rechecked afterwards, but it bound immediately like that…
All the best and thanks for this guide!


#92

Hi all !

I need to understand something with my sticks…
I am flying mode 4 (yaw on the right / Roll on the left) and nothing on the sticks commands below is correct:

It is impossible to bind using throttle right down and yaw in the middle…


#93

But I have found the way to bind (in trying so many times…) with this scheme with throttle down and yaw on the right :

It works! And I can fly my micro quad (disarm is yaw on the left then)

Please someone explain me why in mode 4 nothing works as it should??
Thanks!


#94

Hi,
I’m having problems with my scisky since about 2 months due to me being a noob. Wrong polarization, nearly messed the bypass since I never soldered, not able to get the green light solid or off and now that I reflashed the scisky I just can’t turn the OneShot feature off no matter what I do. Does someone know how to fix this and why it always automatically turns on after I try to save?
(Also my dx6i throttle can only go min 1080 and max 1945 is that a problem?)
Here’s my cli dump if it Helps:
Thanks In Advance

version

BetaFlight/NAZE 2.8.1 Jun 19 2016 / 20:31:03 (0c5ea0f)

dump master

mixer

mixer QUADX
mmix reset
smix reset

feature

feature -RX_PPM
feature -VBAT
feature -INFLIGHT_ACC_CAL
feature -RX_SERIAL
feature -MOTOR_STOP
feature -SERVO_TILT
feature -SOFTSERIAL
feature -GPS
feature -FAILSAFE
feature -SONAR
feature -TELEMETRY
feature -CURRENT_METER
feature -3D
feature -RX_PARALLEL_PWM
feature -RX_MSP
feature -RSSI_ADC
feature -LED_STRIP
feature -DISPLAY
feature -ONESHOT125
feature -BLACKBOX
feature -CHANNEL_FORWARDING
feature -TRANSPONDER
feature -AIRMODE
feature -SUPEREXPO_RATES
feature VBAT
feature RX_SERIAL
feature MOTOR_STOP
feature FAILSAFE
feature ONESHOT125
feature SUPEREXPO_RATES

beeper

beeper GYRO_CALIBRATED
beeper RX_LOST
beeper RX_LOST_LANDING
beeper DISARMING
beeper ARMING
beeper ARMING_GPS_FIX
beeper BAT_CRIT_LOW
beeper BAT_LOW
beeper GPS_STATUS
beeper RX_SET
beeper ACC_CALIBRATION
beeper ACC_CALIBRATION_FAIL
beeper READY_BEEP
beeper MULTI_BEEPS
beeper DISARM_REPEAT
beeper ARMED
beeper SYSTEM_INIT
beeper ON_USB

map

map TAER1234

serial

serial 0 1 115200 57600 0 115200
serial 1 64 115200 57600 0 115200

led

led 0 15,15:ES:IA:0
led 1 15,8:E:WF:0
led 2 15,7:E:WF:0
led 3 15,0:NE:IA:0
led 4 8,0:N:F:0
led 5 7,0:N:F:0
led 6 0,0:NW:IA:0
led 7 0,7:W:WF:0
led 8 0,8:W:WF:0
led 9 0,15:SW:IA:0
led 10 7,15:S:WF:0
led 11 8,15:S:WF:0
led 12 7,7:U:WF:0
led 13 8,7:U:WF:0
led 14 7,8:D:WF:0
led 15 8,8:D:WF:0
led 16 8,9::R:3
led 17 9,10::R:3
led 18 10,11::R:3
led 19 10,12::R:3
led 20 9,13::R:3
led 21 8,14::R:3
led 22 7,14::R:3
led 23 6,13::R:3
led 24 5,12::R:3
led 25 5,11::R:3
led 26 6,10::R:3
led 27 7,9::R:3
led 28 0,0:::0
led 29 0,0:::0
led 30 0,0:::0
led 31 0,0:::0

color

color 0 0,0,0
color 1 0,255,255
color 2 0,0,255
color 3 30,0,255
color 4 60,0,255
color 5 90,0,255
color 6 120,0,255
color 7 150,0,255
color 8 180,0,255
color 9 210,0,255
color 10 240,0,255
color 11 270,0,255
color 12 300,0,255
color 13 330,0,255
color 14 0,0,0
color 15 0,0,0

aux

aux 0 0 0 1025 1250
aux 1 1 1 1050 1250
aux 2 2 1 1750 1950
aux 3 0 0 900 900
aux 4 0 0 900 900
aux 5 0 0 900 900
aux 6 0 0 900 900
aux 7 0 0 900 900
aux 8 0 0 900 900
aux 9 0 0 900 900
aux 10 0 0 900 900
aux 11 0 0 900 900
aux 12 0 0 900 900
aux 13 0 0 900 900
aux 14 0 0 900 900
aux 15 0 0 900 900
aux 16 0 0 900 900
aux 17 0 0 900 900
aux 18 0 0 900 900
aux 19 0 0 900 900

adjrange

adjrange 0 0 0 900 900 0 0
adjrange 1 0 0 900 900 0 0
adjrange 2 0 0 900 900 0 0
adjrange 3 0 0 900 900 0 0
adjrange 4 0 0 900 900 0 0
adjrange 5 0 0 900 900 0 0
adjrange 6 0 0 900 900 0 0
adjrange 7 0 0 900 900 0 0
adjrange 8 0 0 900 900 0 0
adjrange 9 0 0 900 900 0 0
adjrange 10 0 0 900 900 0 0
adjrange 11 0 0 900 900 0 0
adjrange 12 0 0 900 900 0 0
adjrange 13 0 0 900 900 0 0
adjrange 14 0 0 900 900 0 0

rxrange

rxrange 0 1000 2000
rxrange 1 1000 2000
rxrange 2 1000 2000
rxrange 3 1000 2000

servo

servo 0 1000 2000 1500 90 90 100 -1
servo 1 1000 2000 1500 90 90 100 -1
servo 2 1000 2000 1500 90 90 100 -1
servo 3 1000 2000 1500 90 90 100 -1
servo 4 1000 2000 1500 90 90 100 -1
servo 5 1000 2000 1500 90 90 100 -1
servo 6 1000 2000 1500 90 90 100 -1
servo 7 1000 2000 1500 90 90 100 -1

set mid_rc = 1500
set min_check = 1100
set max_check = 1900
set rssi_channel = 0
set rssi_scale = 30
set rssi_ppm_invert = OFF
set input_filtering_mode = OFF
set roll_yaw_cam_mix_degrees = 0
set max_aux_channels = 6
set debug_mode = NONE
set min_throttle = 1150
set max_throttle = 1850
set min_command = 1150
set anti_desync_power_step = 0
set servo_center_pulse = 1500
set 3d_deadband_low = 1406
set 3d_deadband_high = 1514
set 3d_neutral = 1460
set 3d_deadband_throttle = 50
set unsynced_fast_pwm = OFF
set fast_pwm_protocol = ONESHOT125
set motor_pwm_rate = 32000
set servo_pwm_rate = 50
set disarm_kill_switch = ON
set gyro_cal_on_first_arm = OFF
set auto_disarm_delay = 10
set small_angle = 25
set fixedwing_althold_dir = 1
set reboot_character = 82
set serialrx_provider = SPEK1024
set sbus_inversion = ON
set spektrum_sat_bind = 0
set spektrum_sat_bind_autoreset = 1
set telemetry_switch = OFF
set telemetry_inversion = OFF
set frsky_default_lattitude = 0.000
set frsky_default_longitude = 0.000
set frsky_coordinates_format = 0
set frsky_unit = IMPERIAL
set frsky_vfas_precision = 0
set frsky_vfas_cell_voltage = OFF
set hott_alarm_sound_interval = 5
set battery_capacity = 0
set vbat_scale = 110
set vbat_max_cell_voltage = 43
set vbat_min_cell_voltage = 33
set vbat_warning_cell_voltage = 35
set vbat_hysteresis = 1
set vbat_pid_compensation = OFF
set current_meter_scale = 400
set current_meter_offset = 0
set multiwii_current_meter_output = OFF
set current_meter_type = ADC
set align_gyro = DEFAULT
set align_acc = DEFAULT
set align_mag = DEFAULT
set align_board_roll = 0
set align_board_pitch = 0
set align_board_yaw = 0
set max_angle_inclination = 700
set gyro_lpf = OFF
set gyro_sync_denom = 8
set gyro_lowpass = 100
set moron_threshold = 42
set imu_dcm_kp = 2500
set imu_dcm_ki = 0
set alt_hold_deadband = 40
set alt_hold_fast_change = ON
set deadband = 6
set yaw_deadband = 6
set throttle_correction_value = 0
set throttle_correction_angle = 800
set yaw_control_direction = 1
set yaw_motor_direction = 1
set tri_unarmed_servo = ON
set servo_lowpass_freq = 400
set servo_lowpass_enable = OFF
set airmode_activate_throttle = 1350
set failsafe_delay = 10
set failsafe_off_delay = 10
set failsafe_throttle = 1000
set failsafe_kill_switch = OFF
set failsafe_throttle_low_delay = 100
set failsafe_procedure = ON
set rx_min_usec = 885
set rx_max_usec = 2115
set gimbal_mode = NORMAL
set acc_hardware = AUTO
set acc_lpf_hz = 10.000
set accxy_deadband = 40
set accz_deadband = 40
set acc_unarmedcal = ON
set acc_trim_pitch = 0
set acc_trim_roll = 0
set baro_tab_size = 21
set baro_noise_lpf = 0.600
set baro_cf_vel = 0.985
set baro_cf_alt = 0.965
set baro_hardware = AUTO
set mag_hardware = AUTO
set mag_declination = 0
set pid_process_denom = 1
set blackbox_rate_num = 0
set blackbox_rate_denom = 0
set blackbox_device = SERIAL
set magzero_x = 0
set magzero_y = 0
set magzero_z = 0
set ledstrip_visual_beeper = OFF

rxfail

rxfail 0 a
rxfail 1 a
rxfail 2 a
rxfail 3 a
rxfail 4 h
rxfail 5 h
rxfail 6 h
rxfail 7 h
rxfail 8 h
rxfail 9 h
rxfail 10 h
rxfail 11 h
rxfail 12 h
rxfail 13 h
rxfail 14 h
rxfail 15 h
rxfail 16 h
rxfail 17 h

profile

profile 0
############################# PROFILE VALUES ####################################

set yaw_p_limit = 500
set dterm_lowpass = 50
set dynamic_iterm = ON
set iterm_ignore_threshold = 200
set yaw_iterm_ignore_threshold = 35
set yaw_lowpass = 80
set pid_controller = LUX
set p_pitch = 20
set i_pitch = 40
set d_pitch = 40
set p_roll = 20
set i_roll = 40
set d_roll = 40
set p_yaw = 40
set i_yaw = 40
set d_yaw = 10
set p_alt = 50
set i_alt = 0
set d_alt = 0
set p_level = 60
set i_level = 60
set d_level = 100
set p_vel = 55
set i_vel = 55
set d_vel = 75
rateprofile 0

rateprofile

rateprofile 0

set rc_rate = 100
set rc_rate_yaw = 100
set rc_expo = 10
set rc_yaw_expo = 10
set thr_mid = 50
set thr_expo = 0
set roll_rate = 40
set pitch_rate = 40
set yaw_rate = 60
set tpa_rate = 20
set tpa_breakpoint = 1500


#95

Try to flash Alienflight F1 and you should be fine concerning one shot. This firmware is set up for brushed builts. You only have to set Spektrum 1024 and enable motor stop, setup your modes, RCRate and RCexpo and PIDs + rates and you should be ready to fly.
Betaflight isn’t the best to start with (in my opinion). And especially the newest release isn’t for beginners. And there’s a reason why it’s called beta…

If you’re not able to arm your board, maybe this thread helps. Don’t know, if you already know it.
http://community.micro-motor-warehouse.com/t/help-with-scisky-board-dx6i/1741/23?u=chrisdo
My lowest throttle value on my dx6i with travel adjusted to 125% was 1058, and everything worked fine. Min throttle 1000, Max throttle 2000, min command 1000 in configuration tab.
Don’t know if your minimum throttle value of 1080 is to high for arming.
Maybe you’ll have to raise min_check a little in CLI. But I’m not sure about that.

Also post your min/max throws of all channels on your receiver tab.


#96

The dates in your dump indicates you managed to download betaflight 2.8.1 which had error in saving settings. Download 2.8.1 again. That version was removed from the github and replaced with a new one.

I did not check specifically it happened excatly with that date & time, but around that time so it is a good change you are suffering about that problem


#97

@Nuffe
Good call. Remember reading about that, but forgot it.
Thx for bringing it back to my memory.


#98

2.8.1 did not work with the clean flight configurator for turning off one shot via GUI. You can use the betaflight configurator or
Try this in the cli:
set fast_pwm_protocol=off
save


#99

Thanks alot :smiley: that fixed it.
Now the only problem I’m facing is that the motors spin up when i plug the battery in (even though I turned motor spin off and set the motor pwm rate to 32000 as seen in the dump. Does it have to do with my configuration or my failsafe ?
My min. Throttle I can get on the dx6i is 1079-1080 and max. is 1947


Sorry for the bad quality ^^’


#100

Lower your min command to 1000. Then motors shouldn’t spin when battery is plugged in.
"min_command is the value sent when disarmed (or when armed and motor stop is on, i.e. when we want the motors not to spin). min_throttle is the value sent when armed (with motor stop off)"